Project Pluto

Project Pluto was a United States government program to develop nuclear-powered ramjet engines for use in cruise missiles. Two experimental engines were tested at the United States Department of Energy Nevada Test Site (NTS) in 1961 and 1964.[1]

For the World War II Pipeline Under The Ocean project, see Operation Pluto.

History

On January 1, 1957, the U.S. Air Force and the U.S. Atomic Energy Commission selected the Lawrence Radiation Laboratory (the predecessor of the Lawrence Livermore National Laboratory, LLNL) to study the feasibility of applying heat from nuclear reactors to ramjet engines. This research became known as Project Pluto. The work was directed by Dr. Theodore Charles Merkle, leader of the laboratory's R-Division.

The "Tory-IIC" prototype

Originally carried out at Livermore, California, the work was moved to new facilities constructed for $1.2 million on 8 square miles (21 km2) of Jackass Flats at the NTS, known as Site 401. The complex consisted of 6 miles (10 km) of roads, critical-assembly building, control building, assembly and shop buildings, and utilities. Also required for the construction was 25 miles (40 km) of oil well casing, which was necessary to store the approximately 1,000,000 pounds (450,000 kg) of pressurized air used to simulate ramjet flight conditions for Pluto.[2]

The principle behind the nuclear ramjet was relatively simple: motion of the vehicle pushed air in through the front of the vehicle (ram effect), a nuclear reactor heated the air, and then the hot air expanded at high speed out through a nozzle at the back, providing thrust.[2]

The notion of using a nuclear reactor to heat the air was fundamentally new. Unlike commercial reactors, which are surrounded by concrete, the Pluto reactor had to be small and compact enough to fly, but durable enough to survive a 7,000-mile (11,000 km) trip to a potential target. The nuclear engine could, in principle, operate for months, so a Pluto cruise missile could be left airborne for a prolonged time before being directed to carry out its attack.

The success of this project would depend upon a series of technological advances in metallurgy and materials science. Pneumatic motors necessary to control the reactor in flight had to operate while red-hot and in the presence of intense radiation. The need to maintain supersonic speed at low altitude and in all kinds of weather meant that the reactor, code-named "Tory", had to survive high temperatures and conditions that would melt the metals used in most jet and rocket engines. Ceramic fuel elements would have to be used; the contract to manufacture the 500,000 pencil-sized elements was given to the Coors Porcelain Company.[2]

The proposed use for nuclear-powered ramjets would be to power a cruise missile, called SLAM, for Supersonic Low Altitude Missile. In order to reach ramjet speed, it would be launched from the ground by a cluster of conventional rocket boosters. Once it reached cruising altitude and was far away from populated areas, the nuclear reactor would be made critical. Since nuclear power gave it almost unlimited range, the missile could cruise in circles over the ocean until ordered "down to the deck" for its supersonic dash to targets in the Soviet Union. The SLAM, as proposed, would carry a payload of many nuclear weapons to be dropped on multiple targets, making the cruise missile into an unmanned bomber. It was proposed that after delivering all its warheads, the missile could then spend weeks flying over populated areas at low altitudes, causing secondary damage from radiation. However, the high speed of the missile would spread direct radiation from the reactor over a large territory, keeping ground exposure to low levels. Little to no fallout would be created as the reactor elements would have to be resistant to the airstream in order to function for any time. When the vehicle would eventually crash after exhausting its fuel or due to a mechanical failure, a local radiation hazard would be created by the reactor. Compared to the primary payload, the effect would not be significant. [3][4]

On May 14, 1961, the world's first nuclear ramjet engine, "Tory-IIA", mounted on a railroad car, roared to life for a few seconds. Three years later, "Tory-IIC" was run for five minutes at full power. Despite these and other successful tests, the Pentagon, sponsor of the "Pluto project", had second thoughts. The weapon was considered "too provocative",[5] and it was believed that it would compel the Soviets to construct a similar device, against which there was no known defense. Intercontinental ballistic missile technology had proven to be more easily developed than previously thought, reducing the need for such highly capable cruise missiles. On July 1, 1964, seven years and six months after it was started, "Project Pluto" was canceled.[2]

See also

References
  1. DOE Archived 2012-03-03 at the Wayback Machine
  2. "Nevada National Security Site History: Project Pluto Factsheet" (PDF). Nevada National Security Site.
  3. HEARINGS BEFORE SUBCOMMITTEES OF THE JOINT COMMITTEE ON ATOMIC ENERGY CONGRESS OF THE UNITED STATES EIGHTY-FIFTH CONGRESS SECOND SESSION ON OUTER SPACE PROPULSION BY NUCLEAR ENERGY JANUARY 22, 23, AND FEBRUARY 6, 1958. Washington: U.S. Govt. Print. Off. 1958.
  4. Merkle, T. C. (1959-06-30). "THE NUCLEAR RAMJET PROPULSION SYSTEM". OSTI 4217328. Cite journal requires |journal= (help)
  5. "Muscle in Mothballs". Retrieved 2014-07-21.
  • Initial text taken from a public domain document at DOE
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.