9×25mm Dillon

The 9×25mm Dillon is a pistol wildcat cartridge developed for use in USPSA/IPSC Open guns. The cartridge is made by necking down a 10mm Auto case to 9 mm.

9×25mm Dillon
9×25mm Dillon (left) next to a 10mm Auto (right)
TypePistol
Place of originUnited States
Production history
DesignerDillon Precision
Designed1988
Specifications
Parent case10mm Auto
Case typeRimless, bottleneck
Bullet diameter.356 in (9.0 mm)
Neck diameter.380 in (9.7 mm)
Shoulder diameter.423 in (10.7 mm)
Base diameter.425 in (10.8 mm)
Rim diameter.425 in (10.8 mm)
Rim thickness.0550 in (1.40 mm)
Case length.990 in (25.1 mm)
Overall length1.250 in (31.8 mm)
Case capacity22.8 gr H2O (1.48 cm3)
Rifling twist1 in 16" (406 mm)
Primer typeCenter-fire large pistol
Maximum pressure37,500 psi (259 MPa)
Ballistic performance
Bullet mass/type Velocity Energy
90 gr (6 g) Gold Dot JHP 2,100 ft/s (640 m/s) 881 ft⋅lbf (1,194 J)
95 gr (6 g) FMJ 2,000 ft/s (610 m/s) 844 ft⋅lbf (1,144 J)
115 gr (7 g) Speer Gold Dot JHP 1,800 ft/s (550 m/s) 827 ft⋅lbf (1,121 J)
125 gr (8 g) FMJ-FP Match or Speer Gold Dot JHP 1,700 ft/s (520 m/s) 802 ft⋅lbf (1,087 J)
147 gr (10 g) FMJ-FP 1,495 ft/s (456 m/s) 730 ft⋅lbf (990 J)
Test barrel length: 6" (Lone Wolf SS 1:16" twist)
Source(s): DoubleTap Ammunition products page

History

Around 1987, Randy Shelley, an employee of Dillon Precision, necked down 10mm Auto brass to 9 mm. His goal was to get as much slow-burning powder in the case as possible in order to drive a 9 mm bullet to the velocity needed to qualify for the then-IPSC major power factor of 175. The short-necked and steep-shouldered cartridge holds twice the powder of a .38 Super Auto case.[1]

The 9×25mm Dillon was used by several notable IPSC shooters, such as Rob Leatham and Jack Barnes.[2]

Most shooters, looking at the 9×25mm Dillon today, focus on the extreme velocities of which it is capable. A 115 grain bullet at 1,800 fps is more than needed for competition. There, a 115 only needed to be going a bit over 1,500 fps to make major. What competitors in the late 1980s and early 1990s who were using the 9×25mm Dillon were doing was adjusting the powder used, to produce more pressure in the compensator, or muzzle brake. A muzzle brake works by diverting gases perpendicularly relative to the barrel to reduce felt recoil. The greater the gas volume, or the pressure that gas is at, the more force the compensator or muzzle brake creates. Competitors could "feed" the compensator more gases. However, the muzzle blast created by the combination proved to be tiring over the course of a match, and the resulting recoil re-direction proved hard on elbows and shoulders. Leatham developed loads with less blast and shock to mitigate this, but discovered there was little advantage over a similar load in .38 Super.[3]

What finally put an end to the 9×25mm Dillon in competition was component wear, magazine capacity and lowering of the USPSA major power factor from 175 to 165 (160 for IPSC competition). Barrels and compensators in high-pressure cartridges like .38 Super at major velocities have a much shorter service life than lower-pressure ones. For maximum-permitted length magazines as used in USPSA/IPSC competition, a .38 Super magazine holds more rounds than a 9×25mm Dillon magazine. With the lowering of the USPSA power factor, safety and effectiveness of .38 Super loads improved to a point that the 9×25mm Dillon was no longer competitive and once worn out, pistols were often retired or rebuilt in .38 Super.

Cartridge dimensions

The 9×25mm Dillon has 1.48 ml (22.8 grains) H2O cartridge case capacity.

9×25mm Dillon maximum cartridge dimensions.[4] All sizes in millimeters (mm).

Americans would define the shoulder angle at alpha/2 = 30 degrees. The common rifling twist rate for this cartridge is 406 mm (1 in 16 in), 6 grooves, Ø lands = 8.79 mm, Ø grooves = 9.02 mm, land width = 3.07 mm and the primer type is large pistol.

According to the QuickLOAD database the 9x25mm Dillon case can handle up to 250 MPa (36,259 psi) piezo pressure. Since there are no C.I.P. or SAAMI limits and data sets for wildcat cartridges this data has to be regarded with caution.

The Austrian 9×25mm Super Auto G pistol cartridge is probably the closest ballistic twin of the 9×25mm Dillon. These cartridges are both necked down 9 mm variants of the 10 mm Auto cartridge though they dimensionally vary.

Reloading

Making the 9×25mm Dillon is fairly easy. Dillon Precision makes the necessary resizing die and reliable reloading data is easily found. Most people were using 115 grain bullets, but bullets with weights as low as 80 grains were used too.

Commercial availability

Loaded cartridges: As of 2016, DoubleTap offers six 9×25mm Dillon factory ammunition loads from 80 to 180 grains.[5] Underwood Ammo offers three 9×25mm Dillon factory ammunition loads from 90 to 125 grains.[6]

Conversions: Drop-in barrels are available as aftermarket parts for the Glock 40, Glock 20 and Glock 29 semi-automatic pistols.[7] These pistols are originally chambered by Glock for parent cartridge of the 9×25mm Dillon, the 10mm Auto.

See also

References
  1. Marshall and Sanow, Street Stoppers, p. 139, Paladin 2006
  2. "The IPSC Dream Team: Champion Guns and Gear" (#1). 1995.
  3. GunGames magazine Issue 1
  4. QuickLOAD software suite
  5. DoubleTap factory loaded 9x25 Dillon ammunition
  6. "Underwood Ammo factory loaded 9x25 Dillon ammunition". Archived from the original on 2016-08-18. Retrieved 2016-07-31.
  7. "Lone Wolf 2008-2009 Catalog" (PDF). Archived from the original (PDF) on 2009-07-11. Retrieved 2009-04-20.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.