Kálmán Kandó
Kálmán Kandó de Egerfarmos et Sztregova (egerfarmosi és sztregovai Kandó Kálmán; 10 July 1869 – 13 January 1931) was a Hungarian engineer, the inventor of phase converter and a pioneer in the development of AC electric railway traction.
Kalman Kando | |
---|---|
Born | 10 July 1869 Pest, Austria-Hungary |
Died | 13 January 1931 61) Budapest, Hungary | (aged
Occupation | engineer |
Education
He was educated at the Budapest Technical University where he gained a diploma in mechanical engineering in 1892. Kandó served as a volunteer for the Austro-Hungarian Navy until 1893.
France
After his military service, he travelled to France, and worked for the Fives-Lille Company in France as a junior engineer, where he designed and developed early induction motors for locomotives. For the manufacture of induction motors, he developed a completely new design-calculation procedure, which made it possible to produce economical AC traction motors for the Fives Lille Company. Within a year, Kandó was appointed as the chief engineer of the electric motor development at the French firm.[1] András Mechwart (the Ganz and Co.’s managing director at that time) asked him to return to Hungary in 1894 and invited him to work at the Electrical Engineering Department of the Ganz Works.
Work on railway electrification
Ganz Company, Budapest
In 1894, Kálmán Kandó developed high-voltage three phase alternating current motors and generators for electric locomotives; he is known as the father of the electric train. His work on railway electrification was done at the Ganz electric works in Budapest. Kandó's early 1894 designs were first applied in a short three-phase AC tramway in Evian-les-Bains (France), which was constructed between 1896 and 1898. It was driven by 37 HP asynchronous traction system.[2][3][4][5][6]
In 1907 he moved with his family to Vado Ligure in Italy and obtained employment with Società Italiana Westinghouse.[7] He would later return to Budapest to work at the Ganz factory where he became the managing director.
Italy, Designing the World's first electrified main railway line
Under his leadership the Ganz factory began work on three-phase haulage for railways. Based on their design, the Italian Ferrovia della Valtellina was electrified in 1902 and became Europe's first electrified main line railway.
For the Valtellina line, three-phase power was supplied at 3,000 volts (later increased to 3,600 volts) through two overhead lines, while the running rails supplied the third phase. At junctions, the two overhead lines had to cross and this prevented the use of very high voltages.
The three-phase, two wire, system was used on several railways in Northern Italy and became known as "the Italian system". There are now few railways which use this system.
In 1907, the Italian government decided for the electrification of another 2000-km railway line and insisted on manufacturing the engines and equipment in Italy. They bought Kandó's patents and put him in charge of the management and design of the new Kandó-type engines and paid licence-fee for the electric motors to the Ganz factory. Two types of locomotives were developed with his leadership in Italy: a 1500 kw cinquanta and a 2100 kw trenta electric locomotives, from which altogether some 700 units were produced. 540 of these were still in service in 1945, the last three-phase line worked until 1976. In honour of Kandó’s work, he was awarded with Commendatore dell'Ordine della Corona d'Italia (Commander of the Order of the Crown of Italy), but in 1915 he had to flee through Switzerland, since Italy entered World War I on the Entente side and declared war on the Austro-Hungarian Monarchy.
Vienna, invention of the phase converter
During World War I between 1916 and 1917, Kandó was a lieutenant completing military service for the Ministry of Defence in Vienna. He worked out a revolutionary system of phase-changing electrical hauling, whereby locomotives were powered by the standard, 50-period, single-phase alternating current used in the national energy supply system. He was the first who recognised that an electric train system can only be successful if it can use the electricity from public networks. In 1918,[8] Kandó invented and developed the rotary phase converter, enabling electric locomotives to use three-phase motors whilst supplied via a single overhead wire, carrying the simple industrial frequency (50 Hz) single phase AC of the high voltage national networks.[9]
Hungary
To avoid the problems associated with the use of two overhead wires, Kandó developed a modified system for use in Hungary. Power semiconductors not having been invented yet in the 1930s, the Kandó V40 locomotives' systems relied on electromechanics and electrochemistry.
Kandó synchronous phase converter
Single-phase power was supplied at 16,000 volts and 50 Hz through a single overhead line and converted to three-phase on the locomotive by a rotary phase converter.[10] The drive motors, made by Metropolitan-Vickers, had a very large diameter of 3 meters and incorporated four sets of 24 magnetic poles each, which could be added to the traction effort at will, producing highly efficient constant speeds of 25, 50, 75 and 100 km/h over rail (or 17/34/51/68 km/h for the V60 heavy freight train engine variant, which had six pairs of smaller driving wheels).
He created an electric machine called a synchronous phase converter, which was a single-phase synchronous motor and a three-phase synchronous generator with common stator and rotor.
It had two independent windings:
- The outer winding is a single-phase synchronous motor. The motor takes the power from the overhead line.
- The inner winding is a three-phase (or variable-phase) synchronous generator, which provides the power for the three- (or more) phase traction motors.
- Power factor
A major benefit of this arrangement was a power factor of nearly 1.00 in the catenary-attached equipment, which fulfilled the electric powerplants' strict load-distributing regulations. The unacceptably poor power factor of pre-World War II design electric motors (occasionally as low as 0.65) was not felt outside the Kando locomotives, as the phase changer machinery provided isolation.
- Speed control
Intermediate speeds were maintained by connecting a water and saltpeter based adjustable resistor to the line, which reduced the efficiency of the locomotive. Timetables for electrified lines were supposed to allow use of full efficiency constant speeds most of the time but, in practice, the need to share the track with trains hauled by MÁV Class 424 steam locomotives meant the water-hungry and wasteful "gearbox resistor" had to be used often.
- Kandó triangle drive
The propulsive force was transferred to the locomotive's wheels using a traditional pushrod system, designed to provide manufacturing and maintenance commodity to the predominantly steam-based Hungarian Railways (MÁV) of the time. The so-called Kandó triangle arrangement [11] transferred power from the electric motor to the pushrods in such a way that no oblique forces were exerted on the chassis, making the V40 less hurtful to the rail track compared to steam engines. In practice the V40 pushrod system was too precise for steam-era habits based maintenance and required more frequent care.
- Shaft drive
More than a decade after Kandó's death two new, shaft-driven prototypes of his design were built by the Ganz company, to allow for 125 km/h traction speeds. The V44 electric locomotives [12] proved too heavy for general use, owing to their 22 metric ton per axle rail load. Both vehicles were eventually destroyed in USAAF bombing raids in 1944, running only 16,000 kilometers overall.
- Bogie-mounted motors
After the second World War, a last series of electric phase-changer locomotives were built by the new communist government in Hungary. Owing to Cold War restrictions, the innovative V55 type,[13] which used bogie-mounted motors, had to be constructed of domestic components entirely and suffered from reliability problems in their double-conversion phase-changer / frequency-changer propulsion system. (The traction motors of pre-WWII V40 and V60 locomotives were made in Britain by the Metropolitan-Vickers company, as part of an economic aid programme organized by Lord Rothermere.)
- Preservation
Currently one example of the V40,[14] the V55 [15] and the V60 locomotive [16] each survives. They are preserved at the Budapest Railway History Park, but require restoration after decades of open air static display. If funding permits, the repaired V40 may return to the open track for "nostalgic service", with a semiconductor front-end added to its system for 25 to 16 kV AC down-step conversion.
France
Kandó designed in 1926 the 1.5 kV DC 2BB2 400 (fr:2BB2 400) for the Paris-Orleans line which were the strongest DC locomotives in Europe at that time.
United Kingdom
There were plans to use the two-wire, three-phase, system on the Portmadoc, Beddgelert and South Snowdon Railway in Wales and the Metropolitan Railway in London but neither of these plans came to fruition due to the outbreak of WW II.
Kandó's legacy
Kálmán Kandó died at Budapest in 1931 but his work lives on. Many modern electric trains work on the same three-phase high tension AC principle introduced by the Kandó V40 locomotives, but the rotary converter is replaced by semiconductor devices. Three-phase powered electric motors allow for high traction effort even at great speeds and the difficulty of maintaining arbitrary speeds at full efficiency is eliminated by using IGBT semiconductors and the use of digital controls.
In Miskolc, the square in front of the Tiszai railway station, where his statue is also standing, bears his name, as well as a vocational secondary school. In Budapest, the Kandó Kálmán Faculty of Electrical Engineering (formerly an independent technical college, now part of Óbuda University), also bears his name. The minor planet 126245 Kandókálmán was named after him.
See also
References
- Antal Ildikó (2014): A magyar villamosenergia-ipar 1896–1914
- Andrew L. Simon (1998). Made in Hungary: Hungarian Contributions to Universal Culture. Simon Publications LLC. p. 264. ISBN 9780966573428.
Evian-les-Bains kando.
- Francis S. Wagner (1977). Hungarian Contributions to World Civilization. Alpha Publications. p. 67. ISBN 9780912404042.
- C.W. Kreidel (1904). Organ für die fortschritte des eisenbahnwesens in technischer beziehung. p. 315.
- Elektrotechnische Zeitschrift: Beihefte, Volumes 11-23. VDE Verlag. 1904. p. 163.
- L'Eclairage électrique, Volume 48. 1906. p. 554.
- "Kálmán Kandó | Óbudai Egyetem". uni-obuda.hu. October 8, 2015.
- Michael C. Duffy (2003). Electric Railways 1880-1990. IET. p. 137. ISBN 9780852968055.
- Hungarian Patent Office. "Kálmán Kandó (1869–1931)". www.mszh.hu. Retrieved 2008-08-10.
- "Image: SPLIT33.JPG, (459 × 534 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.
- "Image: ka_drv.jpg, (734 × 377 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.
- "Image: V44_1.JPG, (764 × 456 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.
- "Image: V55_1.JPG, (726 × 432 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.
- "Image: ka1.jpg, (645 × 363 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.
- "Image: V55.jpg, (1275 × 856 px)". upload.wikimedia.org. 2004-08-06. Retrieved 2015-10-09.
- "Image: V60.jpg, (686 × 322 px)". erojr.home.cern.ch. Archived from the original on 2011-07-06. Retrieved 2015-10-09.