Current limiting

Current limiting is the practice in electrical and electronic circuits of imposing an upper limit on the current that may be delivered to a load to protect the circuit generating or transmitting the current from harmful effects due to a short-circuit or overload.

Inrush current limiting
Main article: Inrush current limiter

An inrush current limiter is a device or group of devices used to limit inrush current. Passive resistive components such as resistors or negative temperature coefficient (NTC) thermistors are simple options, with power dissipation and cool-down time being their main drawbacks, respectively. More complex solutions using active components can be used when simpler options are unsuitable.

In electronic power circuits
Active current limiting or short-circuit protection

Some electronic circuits employ active current limiting, since a fuse may not protect solid-state devices.

One style of current limiting circuit is shown in the image. The schematic is representative of a simple protection mechanism used in regulated DC supplies and class-AB power amplifiers.

Q1 is the pass or output transistor. Rsens is the load current sensing device. Q2 is the protection transistor which turns on as soon as the voltage across Rsens becomes about 0.65 V. This voltage is determined by the value of Rsens and the load current through it (Iload). When Q2 turns on, it removes base current from Q1 thereby reducing the collector current of Q1. which is very nearly the load current. Thus, Rsens fixes the maximum current to a value given by 0.65/Rsens. For example, if Rsens = 0.33 Ω, the current is limited to about 2 A even if Rload becomes a short (and Vo becomes zero).

Further, this power dissipation will remain as long as the overload exists, which means that the devices must be capable of withstanding it for a substantial period. This power dissipation will be substantially less than if no current limiting circuit had been provided. In this technique, beyond the current limit the output voltage will decrease to a value depending on the current limit and load resistance.

V-I curves for voltage regulators with different overload handling: foldback, constant current limited, and unlimited.

To reduce the heat that must be dissipated by the pass devices under a short-circuit, foldback current limiting is used, which reduces current in the short-circuit case. Under a short circuit, where the output voltage has reduced to zero, the current is typically limited to a small fraction of the maximum current.

Power dissipation vs. load resistance for linear voltage regulators with different overload handling. Here Vin = 12 V, VOC = 10 V, Imax = 1 A, ISC=0.17 A. The maximum dissipation in the foldback design is three times lower than in the constant current limited design.

The prime purpose of foldback current limiting in linear power supplies is to keep the output transistor within its safe power dissipation limit. A linear regulator dissipates the difference between input and output voltages as heat. Under overload conditions the output voltage falls and so the difference becomes larger, thus increasing dissipation. Foldback helps to keep the output transistor within its safe operating area under fault and overload conditions. Foldback also significantly reduces the power dissipation in the load in fault conditions, which can reduce the risks of fire and heat damage.[1]

Many power supplies employ constant current limiting protection; foldback goes one step further by reducing the output current limit linearly as output voltage decreases. However it adds complexity to the power supply and can trigger "lockout" conditions with non-ohmic devices that draw a constant current independent of supply voltage (such as op-amps). A foldback current limiter may also employ a transient delay to both avoid lockout and limit localized heating at the short circuit.

A switched-mode power supply operating at the current limit with the output short circuited does not have increased power dissipation in the power transistor(s), so foldback current limiting is an application feature only rather than one that also prevents a load fault from also destroying the power supply. The safety benefit of reducing the power delivered to a short circuit in the load is proportional to the operating current limit. Foldback current limiting is most likely to be found in a switchmode power supply when it is a component in a product that is independently certified to meet regional safety standards. [2]

The inrush current of an incandescent lamp causes a bench power supply to limit its output current with a foldback current limiter.

Single power-supply circuits
Current limiter with NPN transistors (Vo output is located at similar location as PNP example)
Current limiter with PNP transistors

An issue with the previous circuit is that Q1 will not be saturated unless its base is biased about 0.5 volts above Vcc.

These circuits operate more efficiently from a single (Vcc) supply. In both circuits, R1 allows Q1 to turn on and pass voltage and current to the load. When the current through R_sense exceeds the design limit, Q2 begins to turn on, which in turn begins to turn off Q1, thus limiting the load current. The optional component R2 protects Q2 in the event of a short-circuited load. When Vcc is at least a few volts, a MOSFET can be used for Q1 for lower dropout voltage. Due to its simplicity, this circuit is sometimes used as a current source for high-power LEDs.[3]

See also

References
  1. Paul Horowitz, Winfield Hill, The Art of Electronics Second Edition, Cambridge University Press, 1989 ISBN 0-521-37095-7, p.316
  2. Keith H. Billings (1999). Switchmode power supply handbook. McGraw-Hill Professional. p. 1.113. ISBN 978-0-07-006719-6.
  3. "The New Stuff!!! Constant Current Source #1". Instructables. Retrieved 4 July 2012.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.